LDS-6 부분방전진단시스템(for IEC60270 Standards) IEC 60270, VDE 0434 표준준수

실제가격이 아닙니다. 주문시 문의바랍니다.SF6 가스가 채워진 데드(Dead) 탱크 차단기 및 변압기사용

판매가격

가격문의

브랜드	DOBLE
제조사	DOBLE
제품코드	LDS-6

주문수량

바로구매 장바구니

The Doble LDS-6 is a highly sophisticated digital measuring system for partial discharge detection and analysis.
It is trusted as a valuable tool for factory and laboratory testing.

The LDS-6 can be used to test a variety of high voltage apparatus.
Use the LDS-6 to perform PD quality tests on motors, generators, transformers,
MV and HV cable systems, switchgear and additional HV accessories.

The LDS-6 complies with IEC 60270, VDE 0434 as well as various IEEE and other standards

Sensors & Accessories

Calibrators

	LDC-5 Calibrator For external calibration of the standard PD measuring circuit according to IEC 60270 Quantifying of the main PD quantity “apparent charge” Output for calibrating pulse charges: 5, 20, 100, 500 pC.
	LDC-5 /D Calibrator Double impulse calibrator For external calibration of the standard PD measuring circuit according to IEC 60270 (single pulses) PD measurements on long cables and in accordance with standards requiring the verification of the double pulse behavior of the employed PD measuring system Produces these standardized time parameters according to the IEC 855-3 Output for calibrating pulse charges (5, 20, 100, 500 pC)
	LDC-5/RIV External RIV calibrator for standardized PD measuring circuit according to IEC 60270 Quantifies “apparent charge” Magnitude of the calibrating pulses can be selected by the “Charge Magnitude” switch
	LDC-5/S2 Charge injector designed for simulation of PD pulses, especially for on-site PD testing Generates five different charge magnitudes, which appear at the 5 BNC-jacks Calibrating charge can be fed into the terminals of test sample (according to IEC 60270 and DIN VDE 0434)

Sensors & Accessories

	PDDC-17 PD Decoupler For use with rotating machines Designed for PD signal transmission with a bandwidth above 30 MHz at 50 Ohm matching resistance PD decoupling unit with integrated PD measuring impedance for decoupling of PD pulses from the standard PD measuring circuit acc. to IEC 60270 Voltage signal for phase resolved measurements Composite PD and voltage signal, additive superimposed
	PDDC-24 Failsafe & LF Coupler For use with rotating machines. Designed for PD signal transmission with a bandwidth above 30 MHz at 50 Ohm matching resistance Transmits test voltage signals at the same wire PD decoupling unit with integrated PD measuring impedance for decoupling of PD pulses from the standard PD measuring circuit according to IEC 60270 Voltage signal for phase resolved measurements Composite PD and voltage signal, additive superimposed Integrated high-voltage fuse
	BC Matching Unit For use with rotating machines Works with your previously installed couplers for PD testing in rotating machines Designed to adapt conventional PD measuring methods to the 80pF-Line coupler Improves signals from existing couplers Avoids outages that would be needed to replace high frequency couplers with low frequency couplers
	LDM-5/SP1 For use with PDDC range Splitting box designed for PD/TV-signal transmission Compact device with all input and output lines at the sides Includes fast overvoltage protection to help prevent dangerous overvoltage due to unexpected breakdown of the test sample
	Connection Boxes For use with LDM-5/U5 Connection Boxes are designed for PD/TV-signal transmission and diplexing Two and three channel connection box options
	HFCT-300 Sensor For use at cable terminations Hand-held split-core sensor specially designed for coupling out high frequency PD-signals Applicable for PD tests on any part of the PD signal loop between the insulation electrodes where the outgoing and incoming signals do not cancel each other out For highly sensitive PD measurements with superposed line currents or high reactive currents (50/60 Hz) which can reach up to 300 A
	Sensor Pre-Amplifier For use with all kind of UHF sensors High sensitivity and high gain sensor amplifier Special protection circuitry protects the input against excessive input power Integrated soft start reduces the maximum peak current when powering up

Measuring Impedances

	LDM-5/U5 For cable and transformer testing General use measuring impedance designed for the decoupling of the PD current pulses on the PD coupling capacitor, changing in equivalent voltage pulses and forwarding to the PD detector (according to IEC 60270) Voltage signal for phase-resolved measurements by an internal low voltage capacitor for measuring test voltage and forwarding to PD test equipment Output for test voltage value, derived from the coupling capacitor No additional HV divider capacitor is necessary With up to 2 switches for maximum 4 different coupling capacitances
	LDM-5/U-RIV For transformer testing Designed for the decoupling of the PD current pulses on the PD coupling capacitor, changing in equivalent voltage pulses and forwarding to the PD detector (according to IEC 60270) Connects to a bushing tap or a coupling capacitor Low voltage capacitor for measuring test voltage and forwarding to PD test equipment Voltage signal for phase-resolved measurements Output for test voltage value, derived from the coupling capacitor No additional HV divider capacitor is necessary
	LDF-6/FU To be used with LDM-5/U5 Band pass filter designed to improve electromagnetic compatibility in the measuring surroundings Reduction of the disturbing influence of high frequency currents Use between a measuring impedance and PD device
	Coupling Capacitors To be used with LDM-5/U5 The coupling capacitor connects the high voltage with the PD-measuring device Mobile and equipped with the suitable security procedures Capacitance 1 nF CC1000/60: Rated Voltage 60 kV CC1000/120: Rated Voltage 120 kV Capacitance 10 nF CC10000/50: Rated Voltage 50 kV.
	LDM-6/3 To be used with Coupling Capacitors Designed for the decoupling of the PD current pulses on the PD coupling capacitor, changing in equivalent voltage pulses and forwarding to the PD detector (according to IEC 60270) Voltage signal for phase-resolved measurements by an internal low voltage capacitor for measuring test voltage and forwarding to PD test equipment Voltages decoupled from the bushing tap together with the PD signal One signal output (TNC-socket) for voltage signal with added PD signal
	LDM-5/M8 Switching Box For use with specially designed LDS-6 control software Signal switch, specially designed for PD applications Stores all measured PD data for each channel separately (8 measuring files) Can customize a test procedure (test time, sequence of activation of the measuring impedances)

무단수집및 복재를 금합니다 .

상품정보고시

제품명	LDS-6 부분방전진단시스템(for IEC60270 Standards) IEC 60270, VDE 0434 표준준수
판매가격	가격문의
브랜드	DOBLE
제조사	DOBLE

오늘 본 상품 (0)

고객센터

Calibrators

LDC-5 Calibrator

LDC-5 /D Calibrator

LDC-5/RIV

LDC-5/S2

Sensors & Accessories

PDDC-17 PD Decoupler

PDDC-24 Failsafe & LF Coupler

BC Matching Unit

LDM-5/SP1

Connection Boxes

HFCT-300 Sensor

Sensor Pre-Amplifier

Measuring Impedances

LDM-5/U5

LDM-5/U-RIV

LDF-6/FU

Coupling Capacitors

LDM-6/3

LDM-5/M8 Switching Box

반품교환
구입제품의 이상이 있을 경우 - 구입후 7일 이내에 동일제품으로 교환 가능하며 운송비는 판매자 부담입니다. - 다른 제품으로 교환, 또는 이상이 없는 제품과 함께 교환을 원하실 경우 구매자께서 운송비를 부담합니다. 구입제품의 이상이 있을 경우 (색상,사이즈,다른상품교환) - 구입후 7일이내 교환 가능하며 구매자께서 운송비를 부담합니다. !! 주의사항 비닐포장 및 Tag의 폐기 또는 훼손 등으로 상품 가치가 멸실된 경우에는 제한. 반품시에 해당 사은품이 있을 경우 같이 보내주셔야 합니다.
배송안내
결제후 3~7일 이내에 상품을 받아 보실 수 있습니다. 국내 최대의 물류사 옐로우캡택배를 통하여 신속하고 안전하게 배송됩니다. 모든 제품은 착불 발송됩니다. 단 30만원 이상 구입시 무료배송입니다. (제주도를 포함한 도서,산간지역은 항공료 또는 도선료가 추가됩니다.)
결제안내
결제방법은 신용카드, 국민/BC(ISP), 무통장입금, 적립금이 있습니다. 정상적이지 못한 결제로 인한 주문으로 판단될 때는 임의로 배송이 보류되거나,주문이 취소될 수 있습니다.